Skip to content
Home » How to Remove Drywall Texture: DIY Step-by-Step Guide

How to Remove Drywall Texture: DIY Step-by-Step Guide

Struggling to remove textured drywall? It’s a common DIY project with a few straightforward steps that can make a big difference.

By understanding the right tools and techniques, you can achieve a smooth, professional-looking surface that’s ready for painting.

In the following guide, I’ll walk you through the process from start to finish, so you can confidently tackle this project and refresh your walls on your own.

Test If Your Texture Is Painted First

To test if your textured surface is painted first, try scoring a small patch with a utility knife and then soaking it again. If the base remains rigid and intact after soaking, the paint film is holding strong. This indicates that repeated wetting is likely your best method for removal. If the surface starts to soften or peel, scraping might be necessary, but otherwise, skipping it in favor of skim coating is smarter.

Be sure to check for hazardous materials like asbestos or lead before disturbing the surface, as these materials can pose health risks. Painted texture surfaces generally do not yield to simple soaking because the paint adheres tightly to the substrate, making wetting alone ineffective. Protecting your floors and furniture from inevitable drips and dust is crucial, so using quality plastic sheeting as a drop cloth is highly recommended. Plan your approach accordingly to avoid a futile battle with stubborn texture or creating a mess. For large surface preparation or subsequent projects, consider the efficiency of a cordless paint sprayer to save time and effort. If you need to repaint the surface after texturing, using a paint sprayer for latex can provide a smooth, even finish.

Clear the Room and Protect Your Floors

To start, clear the room by removing all movable furniture, wall decor, rugs, and electronics. This prevents dust and debris from settling on or damaging these items. For bulky pieces that cannot be moved, shift them to the center of the room and cover completely with plastic sheeting. Seal doorways with plastic barriers to contain dust and prevent it from spreading to adjacent areas. Cover HVAC vents with plastic to limit airflow through ductwork, which can quickly spread fine particles throughout the space. Keep furniture arranged to maximize open floor space, helping dust settle and making cleanup easier. Lay heavy-duty canvas drop cloths in high-traffic areas, then cover with 6-mil plastic sheeting, taping all seams and edges securely to baseboards. These canvas drop cloths are washable and reusable for future projects. For delicate baseboards and trim, use a gentle-surface masking tape to avoid leaving adhesive residue or causing damage. Extend the coverings a few inches up the walls to form a continuous seal, protecting subfloors from slurry and simplifying final cleanup. Keeping your tools, like an air compressor, free of moisture is also important, which is why many workshops use a refrigerated air dryer for optimal performance.

Gather the Right Tools and Safety Gear

To gather the right tools and safety gear, you need to prioritize personal protective equipment (PPE) and tool maintenance. Your PPE must include a half-face respirator with HEPA or P100 cartridges to filter out fine dust particles. For maximum protection during dusty demolition, ensure you select the best respirator with a secure fit. Seal the respirator tightly and keep the filters sealed until you’re ready to use them. Wear non-fogging goggles designed for overhead work to protect your eyes from dust and debris. Disposable coveralls and gloves are essential to keep dust off your skin and clothing.

Before beginning work, inspect your drywall knives, which should be between 6 and /2 inches in width. Check for any nicks, rust, or dull edges. Sharpen or replace them as needed, because a clean, sharp blade makes scraping more efficient and safer. Keep a spray bottle filled with water nearby for dampening surfaces to reduce dust creation. Use a HEPA-rated wet/dry vacuum for cleanup—standard vacuums can blow dust back into the air. Ensuring your vacuum has a properly functioning air oil separator can significantly improve its efficiency and longevity by protecting the motor from fine particulate damage. For applying smoothing compounds later, choosing a quality angled sash brush can make a significant difference in the finish. Organize your gear so everything is within reach, and ensure your respirator filters remain sealed until you’re ready to work.

Scrape Texture in Small Sections

Break the wall into sections of about 2 to 4 square feet, roughly 3 by 3 feet. This size ensures the texture remains wet and manageable, making it easier to scrape without the material drying out too quickly. Start at the top of the wall and work downward to keep softened material from falling onto areas that haven’t been finished yet. Overlap each section by about 6 inches to avoid hard lines between scraped areas, ensuring a smooth, consistent finish. To protect the finished surface of adjoining walls or trim you aren’t working on, apply a line of high-adhesion painter’s tape. For additional protection of your floors and to create a clean worksite, lay down red rosin paper before beginning the scraping process.

Hold your scraper at a shallow angle between 20 and 30 degrees. This is similar to ensuring the correct gauge settings for an accurate measurement when using a pressure instrument. Use long, gentle, overlapping strokes to peel away the texture in strips or sheets. Regularly clean the blade to prevent buildup that can drag across the wall and cause uneven removal. If you encounter resistance, stop and re-wet the area until it softens further. Forcing the blade can gouge the drywall paper and damage the surface. Maintain a steady pace so the compound stays within the softening window, avoiding drying out between passes.

Smooth the Surface After Texture Removal

To smooth the surface after texture removal, start by inspecting the wall with your hands and a straightedge to identify high spots, low spots, nail pops, or seam ridges. These uneven areas often remain after removing texture, so it’s important to address them before proceeding. Reset any loose fasteners to prevent bumps from recurring later. Use surface preparation techniques by sanding with 80- to 100-grit paper to knock down leftover peaks. For tasks requiring consistent power like sanding, using the correct air compressor lubricant ensures your tools operate smoothly and last longer. Use light, overlapping circular motions and avoid pressing too hard, as heavy pressure can gouge the drywall. Progress to 120- to 150-grit paper for a final smooth finish. Feather any repairs by extending compound beyond the damaged area with a 10- to 12-inch knife, applying thin coats that gradually widen each time. It’s wise to protect your flooring from dust and spills with a durable canvas drop cloth. After sanding, proper tool cleanup is essential; you should avoid washing paint brushes in the sink to prevent plumbing issues and environmental harm. Finish by softening remaining ridges with a final 150-grit pass. Keep dust under control by opening windows and using a vacuum sander. Before priming, check the wall under angled light; it should feel even and look uniform to ensure a smooth surface.

Skim Coat for a Smooth, Paint-Ready Surface

Skim coating creates a smooth, paint-ready surface by filling in remaining imperfections after sanding. To do this, thin the joint compound to a creamy, yogurt-like consistency by adding water gradually. Work in small sections—around three by three feet—and apply the mixture with a roller or knife. Keep each coat under 1/8 inch thick to prevent cracking or sagging.

Use a wide blade held at a shallow angle, pressing firmly to spread the compound evenly and remove excess. This results in a uniform, flat film. Allow each coat to dry fully, typically 24 to 48 hours, before applying another if needed. If you notice leftover imperfections, add a second coat, changing your trowel direction to eliminate tool marks. Before applying subsequent coats, lightly sand any high spots to maintain a smooth surface.

Always clean up between coats—lumps that aren’t removed will transfer into streaks or uneven patches. Your goal is a completely even, smooth surface that’s ready for paint. Proper application of skim coating ensures a professional-looking finish without patterns or texture that other removal methods might leave behind. This technique is a key step in mastering drywall texturing for both renovation projects and new installations.

Prime and Paint to Lock in the Finish

Priming the wall with a PVA drywall primer is essential before painting. Apply a thin, even coat over the entire surface, including patches, to seal the porous drywall and joint compound. This step ensures a uniform finish and prevents unsightly flashing or uneven color absorption. Allow the primer to dry completely, then lightly sand the surface and vacuum away dust. If absorption still appears uneven, applying a second coat will help achieve a smooth, sealed surface. For large projects like this, using a paint sprayer can save considerable time and ensure an even coat, and it’s important to use the correct air hose fittings for any pneumatic tools. Choosing the right high-quality paint brushes for your topcoat will further enhance the final smoothness and precision of the application. Once fully sealed, choose a paint sheen based on the desired finish—flat finishes conceal imperfections best, while higher sheens can highlight flaws. Paint on two coats of latex topcoat, ensuring the primer sealing locks in the base and that the sheen remains consistent. Before completing the process, inspect the surface under strong lighting to catch and fix any missed spots.

Leave a Reply